Table of Contents

Main window – Qt version

This article describes the main window in the Qt graphical user interface, which is the default GUI for the official Microsoft Windows builds of Avidemux. GNOME, Xfce or LXDE users may prefer the GTK+ version.

Main toolbar

The main toolbar allows easy access to the commonly used actions:

Open a video file

Save a video file

Display file information (audio/video format, resolution etc.)

Load and run a project

Save a project

Open a bitrate/filesize calculator – it calculates the video size for 2-pass encoding (because only video size, without audio, is required in the 2-pass encoder settings), clicking the OK button sets the 2-pass video size for the selected encoder

Preview mode

Input – display input (unfiltered) video in the main window

Output – display filtered output in the main window

Side – display both input and output in the main window, horizontally

Top – display input and output stacked vertically

Separate – display input in the main window and output in a separate window

The navigation bar is used for navigation, using the navigation slider on the left and the buttons, playback, selecting parts of the file (cutting) and time information. The blue rectangle marks the current selection.

Start playback

Stop playback

Go to previous frame

Go to next frame

Go to previous intra frame (keyframe)

Go to next keyframe

Go to previous black frame – searching for black frames may take some time and may not be 100% accurate

Go to next black frame

Go to the first frame (beginning)

Go to the last frame (end)

Jog/shuttle, fast-forward or rewind by turning the wheel, speed depends on how far it is turned; keyframe based navigation

Selection

You can either cut or save a selected part of the video.

Set mark A (selection start) to the current frame

Set mark B (selection end) to the current frame

This frame shows the corresponding frame numbers for A and B marks (unless you set A or B marks, the whole video is selected), pressing the buttons with the numbers means “go to mark A” or “go to mark B”

Information

Displays current frame and total number of frames – when you enter a frame number into the current frame text box and press Enter, Avidemux will go to that frame

Displays current time and total time – when you change the time in the current frame text box and press Enter, Avidemux will go to that time

Type of the current frame (I-frame, P-frame or B-frame), the number between brackets shows the quantizer used to encode the displayed image (meaningful only when used with a quantizer type codec like the MPEG codecs)

Volume control

Audio/video sidebar

The toolbar on the left can be used for setting audio and video encoders, filters and the output format.

Audio and video encoders are listed in a “format (encoder)” form, where format is the specification, standard, while encoder is the particular software library, implementation, that encodes the stream to the chosen format. For example, “MPEG-4 ASP (Xvid4)” means the output video format is set to MPEG-4 ASP and the chosen software library used for encoding the MPEG-4 ASP video is Xvid. “MP3 (LAME)” means the output audio format is set to MP3 and LAME is the MP3 encoder.

The “Format” menu is mainly used for setting the output container. A container contains audio and video streams multiplexed into a single file. It is important to select a suitable container format for the audio and video stream types selected in the Audio and Video menus. For example, MPEG-2 (DVD, SVCD) or MPEG-1 (VCD) video should not be saved into an AVI container. Some popular A/V format/container combinations include:

The default video encoder is “Copy”, which means no video encoding, video from the input will be copied to output (filters cannot be applied in Copy mode) – selecting a video encoder from the drop-down list allows you to configure it (the Configure button) and set video filters (the Filters button); if a supported encoder does not appear in the list, it means Avidemux has not been built with support for it

The default audio encoder is “Copy”, which means no audio encoding, audio from the input will be copied to output – selecting an audio encoder for encoding from the drop-down list allows you to configure it (the Configure button) and set audio filters (the Filters button); when the the A/V shift checkbox is checked, audio will by shifted by the number of milliseconds set in the A/V shift spin box

Select the output format; the default A/V container format is AVI